QUICK START GUIDE
Configuration Guide: ARCE STREAMER + ARES 12TH-1 roon & I²S
Configuration Guide: ARCE STREAMER I²S Pinout Modes
-
Press SETUP button once, SETUP LED on. Arce Streamer in Setting Mode
-
In Setting Mode, the push buttons and LEDs on the front panel represent a different meaning.
-
I2S/USB Button = Setting Selection – Left
-
SOURCE Button = Setting Selection – Right
-
-
Press I2S/USB or SOURCE button. The Streaming Service LED will turn on/off according. Stop when ‘roon’ LED is turned on. You are in I2S Setting Mode as the ‘roon’ LED on.
-
Toggle the LOCAL button momentarily, I2S/NET/LOCAL will turn on/off in a fixed pattern to denote binary 000-111
-
Set the I2S Pinout to 000
-
Wait for 5s or Press the SETUP button once again to exit Setting Mode
-
STREAMER back in operational mode
Configuration Guide: ARCE STREAMER External Master Clock Input
-
Press SETUP button once, SETUP LED on. Arce Streamer in Setting Mode
-
In Setting Mode, the push buttons and LEDs on the front panel represent a different meaning.
-
I2S/USB Button = Setting Selection – Left
-
SOURCE Button = Setting Selection – Right
-
-
Press I2S/USB or SOURCE button. The Streaming Service LED will turn on/off according. Stop when ‘Airplay’ LED is turned on. You are in External Clock Setting Mode as the ‘Airplay’ LED on.
-
Toggle the LOCAL button momentarily, NET LED will turn on/off.
-
NET LED Off – Arce uses internal clock
-
NET LED On – Arce uses external clock
-
-
Wait for 5s or Press the SETUP button once again to exit Setting Mode
-
STREAMER back in operational mode
FIRMWARE UPDATE: ARCE STREAMER
-
Load the firmware file to a USB pendrive (FAT32) via a computer
-
​USB pendrive has to be in FAT32 format, storage capacity less than 128GB
-
Copy the firmware file *.TSU to the root folder, i.e. E:\ARCE_SV03.00.20_HV20.TSU
-
-
Plug in the USB pendrive to the Arce Streamer USB port
-
Plug in AC Power Cord. Turn on AC Power Supply
-
Arce Streamer Standby LED on. At this point in time, press and hold the following button
-
I2S/USB​
-
SOURCE
-
-
While holding the two buttons, press Standby button to turn on the streamer
-
LEDs flash to indicate firmware update is in progress. At this point, depress the two buttons.
-
Once the firmware update is completed, all LEDs on the front panel turn on.
-
Unplug the power cord
-
Unplug the USB pendrive
-
Firmware update completed
WARNING: DO NOT INTERUPT THE POWER & USB PENDRIVE WHILE THE FIRMWARE IS BEING UPDATED
FIRMWARE REVISION
SV03.00.20 (Sept 22, 2022)
-----------------------------------------------------
-
Mute output in the event of playback error
-
Disable Local LED flashes when SD/USB storage is detected
-
Stop streaming service(s) when it's not selected as the desire source
-
Revised buffer memory allocation to reducing playback stuttering
-
Added USB Audio Output (trial)
-
I2S/USB LED flashes indicate USB Audio Output is selected, Arce is scanning USB DAC
-
If there is USB DAC connected to the streamer, the I2S/USB LED lid to indicate Arce output via USB. Note: I2S/SPDIF/AES/OPT output will be disabled.
-
To switch between I2S/USB output, press and depress the I2S/USB button
-
I2S/USB LED off - Arce output through i2s/coax/aes/opt
-
I2S/USB LED on/flashes - Arce output through USB
-
-
​
Version | Download | Date |
---|---|---|
SV03.00.20 | 09/22/2023 |